Dwyer Instruments Pty Ltd
As a leading manufacturer in the controls and instrumentation industry, Dwyer Instruments continues to grow and serve major markets including, but not limited to HVAC, chemical, food and beverage, pharmaceutical, oil and gas, wastewater and pollution control.
|Phone:||02 4272 2055|
|Fax:||02 4272 4055|
4/11 Waverley Drive , Unanderra NSW 2526 (Directions)
The Series TDFS thermal flow switch indicates whether the flow rate is above or below a user set flow rate with NO and NC NPN outputs.
The Series 629 differential pressure transmitter monitors differential pressure of air and compatible gases and liquids with 0.5% accuracy.
The series ULF ultrasonic level transmitter for fluids is an ultrasonic continuous flow measurement transmitter which is suitable for maintenance-free, non-contact measurement of open channels. The series operates on ultrasonic technology and offers dependable, accurate measurements.
The Series ULB ultrasonic solid level transmitter is a direct-install level transmitter designed for non-contact measurement of solid levels. The ULB uses ultrasonic technology paired with automatic temperature compensation to provide reliable and accurate measurements in virtually all conditions. An integrated LCD and four responsive push-buttons allow for quick and easy programming on a simple menu structure. Diagnostic capabilities and a failsafe output signal make the ULB suitable for critical applications.
The Series CFS2 cable float switch is a mechanically actuated floating switch intended to activate electrical components, usually pumps, to start and stop automatically.
Monitoring the environmental conditions is more convenient with the Model EMMA environmental multifunction meter. Humidity, temperature, air velocity, airflow, sound and light measurements are combined in one easy-to-use instrument.
The Model 450A-1 digital pocket size carbon monoxide meter measures the ambient concentration of carbon monoxide (CO) in the environment and displays the measurement on the two-line digital LCD screen. Besides the measurement, the maximum recorded CO value since the last reset is shown. An audible carbon monoxide alarm gives warning of CO levels above 25 ppm. For viewing in poorly lit environments, the built-in back light brightens the display.
The AQS-1 AQStick ambient volatile organic compound (VOC) monitor is used to monitor ambient air quality by detecting the VOC content in the air. Some common sources of VOC contamination are carpets, building materials, paints, cleaners and tobacco smoke. Even low concentrations of these compounds can affect building occupants’ comfort. A computer’s USB port provides power for the sensor and the LED lights which change colour in accordance with the ambient air quality.
The SBLT2 and SBLTX submersible level transmitters, suitable for use in harsh applications, both measure the height of liquid above the position in the tank referenced to atmospheric pressure. The transmitters consist of a piezoresistive sensing element, encased in a 316 SS housing. The bullet-nose design protects the diaphragm from damage.
The series DX differential pressure switch can be used for low differential pressure indication with setpoint on a decrease of pressure as low as 1 psid (0.07 bar). Differential setpoint ranges are available from 2.5 to 75 psid (0.17 to 5.17 bar) on increasing differential pressure and 1.0 to 67 psid (0.07 to 4.62 bar) on decreasing differential pressure. The unit features a high static pressure rating of 200 psig (13.8 bar) for higher static pressure applications. It comes standard with a weatherproof, UL type 4X enclosure for dust-laden, outdoor or washdown installation environments.
The Series DX differential pressure switch makes a contact output based on the differential between two pressure sources.
The Mercoid series 3100 smart pressure transmitter is a microprocessor-based high-performance transmitter which has flexible pressure calibration and push-button configuration, and is programmable using HART communication.
The PBLT2 submersible level transmitters measure the height of liquid above the position in the tank, referenced to atmospheric pressure.
The series ISDL intrinsically safe temperature/humidity data logger accurately records temperatures that range from -40 to 80°C. The easy-to-use DL700 software makes retrieving data simple and allows for user-selectable sampling rates. The device can easily be started and stopped from a PC or delayed to start up to six months in advance.
The Series TE Duct and Immersion Temperature Sensor can be used to monitor air or water temperature throughout a building management system or an air handler unit. Flanged duct sensors monitor the supply or return air and provide a thermistor or RTD output to the digital controller. Immersion sensors, which are supplied with compression fittings, are typically used to monitor the hot or chilled water lines throughout a building. Thermowells are recommended, but not required, on the immersion sensors.
The Dwyer Series 626 pressure transmitters possess a claimed precise 0.25% piezoresistive sensor contained in a compact, rugged, NEMA 4X stainless steel, general-purpose housing or cast-aluminium conduit housing.
The Series WMT multi-jet water meter with pulse output is suitable for commercial and industrial applications.
The series UXF3 ultrasonic flowmeter converters are paired with series SX1 or SX2 sensors in order to use the transit-time measure method. Using microprocessor-based electronics, the flowmeter can be configured from the front keypad to specific applications.
The series WMT multi-jet water meter with pulse output is suitable for commercial and industrial applications. The multi-jet design allows simplicity and accuracy with wide flow ranges, even in low flow applications.
The Series BCV are economical, thermoplastic ball check valves suitable for chemical and wastewater applications.
The Series FPV plastic flap check valves are suitable where backflow could potentially cause damage to pumps, filters or process equipment. The valves operate without the need for any adjustments or settings.
Dwyer Instruments Pty Ltd has released its latest Dust Collector Timer Board, the DCT 600.
Dwyer Instruments has released the Series DCT600 dust collector timer controller.
Dwyer Instruments Pty Ltd is announcing the release of its latest Dust Collector Timer Board, the DCT 600.
The Mercoid series CXA water pump pressure switch is a low-cost solution for controlling automatic water systems.
The series UGE Utility Gauges possess dual psi and bar scales with 3-2-3% ANSI B40.1 Grade B accuracy. The gauges are designed with black steel housings and chrome bezels. Wetted parts include a brass socket and phosphor bronze bourdon tube. Units can withstand ambient temperatures of -45 to 71°C.
Diaphragm pulse valves for pulse jet dust collectors are constructed of robust die-cast aluminium with NBR diaphragms. The valves come in a choice of either the series DCV with an integral solenoid coil or the series RDCV that are to be used with a remote solenoid.
Remote pilot solenoid valves for pulse jet dust collectors are constructed of robust die-cast aluminium and 304 SS. The valves come in a choice of either individual valves for customer panel mounting, series RSV or factory mounted in a weatherproof enclosure, series SVE.
WE Anderson has released the Series 3BV3 SS three-way electric and pneumatic ball valves. The three-way port configuration is suitable for mixing or diverting services in pharmaceutical and chemical processing systems.
The Model FS-2 from the WE Anderson division of Dwyer Instruments is a durable paddle style flow switch with an adjustable setpoint. The unit features an adjustable paddle with four selectable lengths for large flow setpoint adjustments and an internal screw for fine adjustments.
The series 2700 current to pressure transducer from WE Anderson is enclosed in a compact IP65 weatherproof FM and CSA intrinsically safe housing. Units have input and output ports on both the front and the back, allowing for versatile plumbing. Designed for remote or panel mounting, optional accessories include DIN rail or pipe mounting kits.
The Series FLST Air Measurement Station is easy to install - simply connect the tubing to the integral station fittings and then to a differential pressure transmitter, gauge or switch. The product is suitable for measuring air velocity in HVAC building applications.
Control and monitor your pumps operation with the new Series MPC Junior Pump Controller from the Mercoid division of Dwyer Instruments.
The Series 631 wet/wet differential pressure transmitter is claimed to reduce cost by eliminating parts by combining a differential pressure gauge with a transmitter.
Control and monitor your pumps operation with the NEW Series MPC Junior Pump Controller from the Mercoid division of Dwyer Instruments.
The series SG stainless steel gauges have dual psi/kPa scales and are available in 2½ and 4" dial sizes. Units are designed with 304 SS housings and either brass wetted parts or 316 SS wetted parts for good chemical compatibility. A wide selection of ranges is available, from full vacuum to 100,000 kPa. These durable gauges can withstand ambient temperatures up to 65°C and process temperatures up to 270°C. The gauges are easily liquid-filled in the field without the need for a separate kit.
The Series DH DigiHelic differential pressure controller is suitable for pressure, velocity and flow applications, achieving a 0.5% full scale accuracy on ranges from 0.25 in wc to 100 in wc. It provides a 4-20 mA process output, 2 SPDT relays with adjustable dead bands, and selection of pressure, velocity or flow operation.